Education, Science, Technology, Innovation and Life
Open Access
Sign In

Research on Integrated Teaching of Science and Education in Engineering Materials Course Based on Properties of Babbitt Alloy

Download as PDF

DOI: 10.23977/curtm.2026.090601 | Downloads: 3 | Views: 153

Author(s)

Yuquan Ni 1, MiaoMiao Li 2, Yuqiang Ma 3

Affiliation(s)

1 School of Mechanical Engineering, Taishan University, Tai'an, 271000, Shandong, China
2 School of Civil and Architectural Engineering, Taishan University, Tai'an, 271000, Shandong, China
3 Department of Intelligent Manufacturing Engineering, Heze Technician College, Heze, 274000, Shandong, China

Corresponding Author

Yuquan Ni

ABSTRACT

The course Fundamentals of Engineering Materials and Forming Technology was plagued by several prominent teaching limitations, including excessively abstract theoretical content, inadequate correlation between material microstructures and macroscopic properties, and a disconnection between forming processes and practical engineering service conditions. These issues led to fragmented knowledge systems among students and failed to fully cultivate students' engineering thinking and practical problem-solving competencies. Adhering to the educational philosophy of integrating scientific research with classroom teaching, this study adopted research findings on Babbitt alloy—a typical wear-resistant material for sliding bearings—as a core teaching carrier. The microstructure characteristics, performance regulation mechanisms, mechanical and tribological properties, and casting forming processes of Babbitt alloy were systematically integrated into classroom teaching. Accordingly, a closed-loop teaching module featuring the logical chain of "microstructure–hardness–tribological performance–forming process" was constructed. Combined with diversified teaching approaches, including problem-driven learning, case-based inquiry, and virtual-reality integrated teaching, the inherent drawbacks of traditional fragmented teaching were effectively addressed. This innovative teaching practice enabled students to clarify the intrinsic correlations among material microstructures, service performances, and forming processes, thereby significantly enhancing students' capabilities in mechanism analysis, process optimization, and engineering problem diagnosis. This study also provided a feasible practical reference for improving the teaching quality of fundamental engineering courses through the transformation and application of scientific research achievements.

KEYWORDS

Microstructure; Tribological Properties; Fundamentals of Engineering Materials and Forming Technology; Curriculum Teaching Reform

CITE THIS PAPER

Yuquan Ni, MiaoMiao Li, Yuqiang Ma. Research on Integrated Teaching of Science and Education in Engineering Materials Course Based on Properties of Babbitt Alloy. Curriculum and Teaching Methodology (2026). Vol. 9, No. 6, 1-7. DOI: http://dx.doi.org/10.23977/curtm.2026.090601.

REFERENCES

[1] Ni, Y., Zhang, W., Song, T, et al. (2026). Bionic-Inspired Design and Tribological Properties of Lamellar Babbitt Alloy With Alternating Coarse–Fine Grain Zones.ASME. J. Tribol. 148(11), 111402. 
[2] Ni Y, Guo P, Ren C, et al. (2023). Differentiated SnSb grain size distribution for improved tribological properties of Babbitt alloy. Industrial Lubrication and Tribology, 75(5), 588-595.
[3] Guo Yaxi, Xie Jingpei, Wang Wenyan, et al. (2009). Effect of casting methods on microstructure and properties of Babbitt alloy. Journal of Henan University of Science and Technology: Natural Science, 30(4),8-11. 
[4] Wei Z , Shu H , Qiao G ,et al. (2025).Performance Improvement of Tin-Based Babbitt Alloy Through Control of Microstructure. Alloys, 4(3), 1-16.
[5] Liu Rui, Yang Chuan, Shi Chengcheng, et al. (2025). Hot deformation behavior and microstructure evolution of lead-based Babbitt alloy. Materials Reports, 39(22), 222-229.
[6] Ni Y, Li X, Dong G , et al. (2019). The combined effect of La and heat treatment on the tribological performances of tin-Babbitt alloy .ARCHIVE Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology, 233(7), 1117-1126.

All published work is licensed under a Creative Commons Attribution 4.0 International License.

Copyright © 2016 - 2031 Clausius Scientific Press Inc. All Rights Reserved.